HyperFlex Water Sealant
HyperFlex is a highly versatile single component, pre-catalyzed hydrophobic polyurethane grout. Because it is pre-catalyzed there is none of the guesswork and expense of field mixing catalyst; simply adjust the temperature of the HyperFlex container to vary your reaction time. Since it is a hydrophobic material shrinking will not be an issue like it can be with hydrophilic materials. HyperFlex is NSF 61-2007 approved for contact with potable water.
Applications:
- Low or high pressure crack injection
- Barrel joint repair
- Annulus grouting
- Underwater leak sealing
HyperFlex is a slower reacting product than our SealGuard II and works well in weeping or low flow leaks. The slower reaction and lower viscosity allows the material to travel further before reaction, allowing for better penetration and coverage within the leaking substrate. Once cured, HyperFlex will form a permanent, non-shrinking seal against further leaks.
- Packaging: 300 ml Caulk Tube
- Transport: USDOT Unregulated Class 55
- Storage: Product is moisture sensitive and should be stored at 60-70⁰. Product should not be exposed to the atmosphere until application. Avoid contact with moisture.
Always read SDS before use.
![]() |
Electric Grout Pump Kit for Hyperflex | |
---|---|---|
Virtually everything one needs to start a polyurethane injection project. This closed pumping system includes a modified Graco 390 ES HighBoy (or equivalent ), 5-gallon pail of Hyperflex, 20 injection packers, gloves, and goggles. Due to pump modifications and the nature of polyurethane grouting, no warranty can be offered. |
||
Price | $2200.00 | |
Qty | ||
![]() |
Hammer Drill Bit 14mm x 600mm | |
DESOI masonary hammer drill bit. 14mm x 600mm (SDS Plus chuck). Used for installation of our 1/2" packers. |
||
Price | $20.00 | |
Qty | ||
![]() |
Manual Injection Hand Pump | |
The DESOI manual reciprocating pump is the perfect device when only small quantities of injection material are needed. Fill the tube with Hyperflex, hook on to the packer, and start the injection work.
Working pressure - 0 - 1450 psi |
||
Price | $75.00 | |
Qty | ||
![]() |
Mechanical Packer Double Check Valve 1/2"(10) | |
High pressure steel 1/2" x 4.75" expanding injection port with zerk fitting. Contains an additional check valve on the inserted end. This enables the stem to be removed without material coming back out. Works best with a 14mm drill bit. Bag of 10 |
||
Price | $50.00 | |
Qty | ||
![]() |
HyperFlex 12 Pack | |
Part# HF12 Comes with twelve 300ml HyperFlex tubes and 12 six inch injection nozzles. May require 3/8 or 1/4 inch drill bit depending on application. |
||
Price | $250.00 | |
Qty | ||
![]() |
HyperFlex 6 Pack | |
Part# HF6 Comes with Six 300ml HyperFlex tubes and 6 six inch injection nozzles. May require 3/8 or 1/4 inch drill bit depending on application. |
||
Price | $140.00 | |
Qty | ||
![]() |
HyperFlex 2 Pack | |
Part# HF2 HyperFlex 2 Pack Comes with two 300ml HyperFlex tubes and 2 six inch injection nozzles. May require a 3/8 or 1/4 inch drill bit depending on application. |
||
Price | $50.00 | |
Qty | ||
![]() |
HyperFlex 5 Gallon | |
Part# HF5G Five gallon pail of Hyperflex. Can be poured from pail or attached directly to a pump. |
||
Price Special Handling* |
$325.00 $10.00 |
|
Qty | ||
![]() |
HyperFlex Caulk Gun | |
Part# CGunHF Super smooth rod revolving frame. 26:1 thrust ratio. Use with 1/10 gallon or 300ML cartridges. |
||
Price | $60.00 | |
Qty | ||
![]() |
Mechanical Packer 5/8" (10) | |
High pressure steel 5/8" x 4.75" expanding injection port with zerk fitting. Works best with a 5/8" drill bit. Bag of 10. |
||
Price | $46.00 | |
Qty | ||
![]() |
Hammer Drill Bit 1/2" x 18" | |
1/2" x 18"x 3/8” Masonry Hammer Drill Bit (Standard Chuck). Used for low pressure injection of Hyperflex.
|
||
Price | $20.00 | |
Qty | ||
* Some products require extra handling due to size and weight, the total postage is shown at checkout. This cost is per item.